Mountain Skeats Claws are for those looking for a more aggressive Skeats skin cleat combined with a minimalist ski crampon. The longer, angled back, front ascent points are paired with even longer side points to aid skiers and splitboarders in navigating steep switchbacks and traversing variable snow and ice. Skeats Claws help overcome ski and splitboard limitations. If your ski/splitboard has a short-radius sidecut or rocker you lose edge and skin traction. These Claws get you that traction back and more. The Skeats Claws give splitboarders the ability to traverse like skiers. Keep the group together! This product is small and packable and can just live in your backpack. You can pack them in an old sunglasses case or simply stow in a hip pouch. The Glide Skeats offer Fin Spikes for greater grip and greater glide!

As a bonus, you will always have two 20" Voile straps with you that can be removed from the Skeats and used independently for any repair/first aid needs. In emergency situations the Skeats Claws can also be used as emergency boot crampons on stiff sole mountaineering and snowboard boots. Skeats Claws are NOT intended as a replacement for mountaineering boot crampons and are only to be used as a last resort to help reach safer terrain. Practice with them in safe terrain and never over any life threatening exposure. Carry proper mountaineering boot crampons on tours requiring them. Skeats are also the perfect option for people who use more than one width of ski, more than one type of binding, more than one splitboard, or who both ski tour and splitboard.

Features

Attachment point width must be equal to or greater than the cleat width purchased. If the cleat width used is wider than the mounting position width, there is risk of bending/damaging the cleat, as well as poor function.
All Skeats products are to be used with touring skins between the base of the ski/splitboard half and the Skeats. If used without touring skins there is risk of ski/splitboard base damage. In case of touring skin glue failure, ensure the touring skin is flat against the base when mounting Skeats to secure the touring skin in place.
The hair on your touring skins may wear around the cleat mounting locations after extended use. Depending on use and mounting tightness, expect some skin hair to wear around the Skeats corners and/or outer profile. Mounting flat and snug/tight against the skin will decrease the probability of touring skin damage.
After mounting and removing Skeats near tour mode toe pieces that use walk mode locking levers, ensure each walk mode lever is pushed down or pulled up per your splitboard or ski binding manufacturer's specified Locked/Walk Position. Depending on your tightening and removal method of the Voile Strap, the strap can lift up or push down the locking lever if mounting Skeats next to it.
Voile Straps are to be inspected for cuts before and after each use, if cuts are observed please replace the 20" Skeats branded aluminum buckle Voile Straps. Only use genuine Voile Straps with aluminum buckles.

Sizing

The mounting position should be just behind the tour mode toe piece; please measure the width of your skis/splitboard halves at the recommended mounting location to determine the best size that will work for you. For skis this is near your waist width, for splitboards this is near half the waist width.

The Skeats 50mm are for mounting position widths from 50mm to 84mm. Use these with skis with a mid waist from 50mm to 84mm.

The Skeats 85mm are for mounting position widths from 85mm to 115mm. Use these with skis with a mid waist from 85mm to 115mm.

The Skeats 105mm‚ will work on skis or boards 105mm or wider.

The Skeats 110mm are for mounting position widths from 110mm to 135mm. These are the most packable option for most splitboards with a mid waist from 220mm to 270mm; so a 110mm to 135mm split ski width. These also work best as emergency soft boot crampons (Side View, Bottom View).

The Skeats 130mm are for mounting position widths from 130mm to 155mm+ for wider splitboards, powder surfer splits and some approach skis. For splitboarders, the Skeats Claws can also be mounted biased to your weaker short radiused edges, so you do not need the size super close to your mounting width and can downsize to the 110mm for packability.

Specifications

(2x) Stainless Steel Skeats Claws (50mm=2x51g=102g/3.6oz, 85mm: 2x70g=140g/5.0oz, 110mm: 2x85g=170g/6.00oz, 130mm: 2x95g=190g/6.7oz), Glide Fins‚ 107 grams per pair
(2x) 20" Aluminum Buckle Voile Straps (2x30g=60g/2.1oz) Made in USA
Total Pair Weight: 50mm=162g/5.7oz, 85mm=200g/7.1oz, 105mm=167g/5.8oz, 110mm=230g/8.1oz, 130mm=250g/8.8oz‚

TOP BRANDS

SPLITBOARD HQ & AQ OUTDOORS

SPLITBOARD HQ &
AQ OUTDOORS